Closeout pass for the G-series 3-ladder chirp + adaptive-escalation work.
Cleanup, watchdog/fallback, lint, full regression — final sign-off.
Cleanup + watchdog/fallback: already wired during earlier audit waves
(track watchdog in chirp_scheduler RP_DEF_TRACK_WATCHDOG_FRAMES, RESERVED
fallback in plfm_chirp_controller_v2, range-decim watchdog in
radar_system_top with gpio_dig7 surfacing, F-3.* MCU error path).
Verified — no residual TODO/FIXME in production RTL or MCU.
Regression infra: tb/cosim/compare_independent.py SKIP-detection bug —
importlib.util.find_spec("scipy.signal") raises ModuleNotFoundError when
the parent scipy package is itself absent (instead of returning None as
the surrounding logic assumed). Wrap in try/except so the regression
runner gets the intended rc=2 SKIP marker rather than a crash that masks
the rest of the script.
Lint sweep: ruff full-repo → 0 errors. Two changes:
- pyproject.toml broadens 5_Simulations/Antenna/**.py exemption from
just T20+ERA to the full set of script-ergonomics rules
(RUF001/002/003 Greek µ/λ/π/θ in physical-units strings, E501 long
matplotlib/numpy lines, RUF005/015/046, E70x one-line setup, B007
tuple-unpack loop vars, B905, BLE001 diag try/except, C401, RET504,
SIM118, PERF40x, ARG001, E402). These are sim/analysis scripts, not
production code — keep substantive bug rules (F unused, B core
bugbears) but drop stylistic noise.
- Auto-fix sweep: 31x F541 (f-string-no-placeholder), 3x F401 (unused
sys import), 2x F841 (dead leftover ref_pat / phases_quant in
array_factor_adar1000_aeris10.py).
.gitignore: cover 9_Firmware/9_2_FPGA/tb/cosim/mf_chain_autocorr.csv
(matched_filter cosim writes here now; was already covered for tb/ but
not tb/cosim/).
Regression baseline (radar_venv):
FPGA : 42/43 — 1 pre-existing T-6 drift cosim fail surfaced by the
SKIP fix above. Three sub-checks now red because PR-O moved
xFFT/MF chain to LogiCORE v9.1 *Scaled* mode (1/2 per stage,
1/2^11 total for N=2048) but compare_independent.py's invariants
(FFT-impulse uniform-spectrum, MF peak-at-injected-delay, MF
peak/median ≥ 5) were written assuming UNSCALED FFT. Not
introduced by this PR — was hidden by the SKIP-detection crash.
Defer to PR-M.4: redesign T-6 invariants (or input amplitudes)
to match scaled-mode arithmetic.
MCU : 34/34 binary suites pass.
GUI : test_v7 150/150 pass.
uv.lock: scipy resolution catch-up (declared in pyproject dev group all
along; lock just hadn't been refreshed after pyproject edits landed).
Bench-side checks: none — this PR is repo hygiene, no firmware/RTL
behaviour change.
Bundled minor-tier fixes from project_aeris10_audit_2026-05-02. No
behavioural changes to the production happy path; mostly stale comments,
defaults, and one new emit-path (m-9) that lets cosim_dir replay show
detections instead of an empty mask.
m-1 — processing.py:59 RadarProcessor.range_doppler_map placeholder
shape (1024, 32) -> (NUM_RANGE_BINS, NUM_DOPPLER_BINS) imported
from radar_protocol so the legacy literal stops leaking to
anything reading the attribute before frame 0.
m-2 — radar_receiver_final.v:596 stale "// 32" comment for
RP_CHIRPS_PER_FRAME -> "// 48 (PR-F: 3 sub-frames * 16)".
m-4 — radar_protocol.py "16384 x 2 = 32768" arithmetic comment was
already corrected by an earlier edit; verified clean.
m-5 — usb_data_interface_ft2232h.v:961 "Frame header: 8 bytes"
comment -> "9 bytes (PR-G: added version byte at offset 1)".
m-6 — radar_system_top.v cold-reset host_chirps_per_elev 32 -> 48
+ status doc-comment so any sanity-checking parser sees the
value matching RP_CHIRPS_PER_FRAME instead of latching a
chirps_mismatch_error.
m-7 — radar_receiver_final.v:370 RX DDC mixers_enable(1'b1)
annotated: documented as intentional asymmetry vs TX (counter-
UAS RX has no quiesce scenario; CDC would add cost without
operational benefit).
m-8 — RadarSettings range_resolution / velocity_resolution flagged
inline as PLACEHOLDER (docstring already explains; inline
marker makes it visible at the field).
m-9 — gen_realdata_hex.py now also emits fullchain_cfar_flags.npy
(uint8 detection mask) and fullchain_cfar_mag.npy (|I|+|Q|),
produced by run_cfar_ca() with the FPGA cold-reset defaults
(guard=2 train=8 alpha=0x30 mode=CA). Replays through
v7.replay's COSIM_DIR loader: 22 detections on the synthetic
scene (was 0). The hex/ directory's two new .npy files are
included in this commit.
Regression: 247/247 (test_v7 130 + test_GUI_V65_Tk 117). Ruff clean.
cosim_dir revival:
- gen_realdata_hex.py: also emit decimated_range_{i,q}.npy (48x512)
and doppler_map_{i,q}.npy (512x48) at production dimensions; the
same Python pipeline that produces the RTL .hex stimuli now writes
the .npy intermediates v7.replay COSIM_DIR loads. Replaces the
workflow lost when golden_reference.py was deleted in e8b495c
- test_v7.py: update test_get_frame_cosim shape from pre-PR-O.6
(64,32) to (NUM_RANGE_BINS, NUM_DOPPLER_BINS)
- check in 4 .npy reference files (~400 KB, deterministic SCENE_SEED=42)
Ruff lint cleanup (was 66 errors; now 0):
- pyproject.toml: ignore T20 in tb/cosim/**.py (CLI tools)
- compare_independent.py: drop redundant int() casts (RUF046),
swap try/except scipy import for importlib.util.find_spec,
remove dead duplicate np import, ASCII-ize comment unicode,
wrap E501 format strings
- fpga_reference.py: drop unused fs arg from nco_reference,
collapse if/else to ternary, mark _out_im unused
- v7/processing.py: ASCII-ize x in docstring, collapse if-branches
- {dashboard,software_fpga,workers,radar_protocol}.py: wrap E501
- test_v7.py: ASCII-ize comment unicode, _alias renames where unused
Result: test_v7 100/100 (0 skips on radar_venv, was 9 graceful
skips); 5 cosim_dir orphan tests now active and passing.
Restore SoftwareFPGA's process_chirps() pipeline by porting the missing
chain stages (MTI canceller, DC notch, CFAR, threshold detection) plus
thin wrappers (range FFT, decimator, Doppler FFT) to fpga_model.py and
swapping software_fpga.py's import target from the deleted
golden_reference.py to fpga_model.
History: golden_reference.py was deleted in e8b495c (the "dead golden
code cleanup") but software_fpga.py kept importing from it. The
ImportError was swallowed at v7/__init__.py:49-52 so package load
succeeded, but every direct `from v7.software_fpga import SoftwareFPGA`
hit the import-time failure — masking 21 broken tests as
"ModuleNotFoundError" instead of surfacing the real issue.
This was actively breaking the GUI replay-from-raw-IQ feature
(dashboard.py:1334-1347, 1577 + GUI_V65_Tk.py:271-300, 1106-1129):
opening a .npy SDR capture instantiates SoftwareFPGA + ReplayEngine;
the dashboard's opcode dual-dispatch routes spinbox changes to the
SoftwareFPGA setters so re-processing reflects live param tweaks.
With the import broken since April, that path silently dies.
fpga_model.py:
- New top-level constants: FFT_SIZE=2048, NUM_RANGE_BINS=512 (from
RangeBinDecimator.OUTPUT_BINS), DOPPLER_CHIRPS=48,
DOPPLER_TOTAL_BINS=48 (track current production: PR-O.6 / PR-F).
- run_range_fft(iq_i, iq_q, twiddle_file): N inferred from input
length; works for legacy 1024-pt and production 2048-pt callers.
- run_range_bin_decimator(range_i, range_q, mode): per-frame wrapper
over RangeBinDecimator.decimate (4x decim -> 512 bins).
- run_mti_canceller(decim_i, decim_q, enable): 2-pulse canceller,
ported verbatim from golden_reference @ commit 237e74c~1.
- run_doppler_fft(mti_i, mti_q): num_subframes inferred from chirp
count; RANGE_BINS overridden per input shape so legacy
2-sub-frame (32-chirp) and production 3-sub-frame (48-chirp)
callers both work.
- run_dc_notch(doppler_i, doppler_q, width): per-bin DC notch,
generalised to any sub-frame count.
- run_cfar_ca(...): CA / GO / SO modes with bit-accurate alpha-q44
threshold + 17-bit saturation, ported from golden_reference.
- run_detection(doppler_i, doppler_q, threshold): |I|+|Q| L1 magnitude
threshold detection.
software_fpga.py:
- _GOLDEN_REF_DIR (cosim/real_data/) -> _FPGA_COSIM_DIR (cosim/)
- `from golden_reference import (...)` -> `from fpga_model import (...)`
- TWIDDLE_1024 -> TWIDDLE_2048 (production 2048-pt range FFT).
- Stage 1 comment: "Range bin decimation (1024 -> 64)" ->
"(production 2048 -> 512)".
- Stage 1 twiddle path picks fft_twiddle_2048.mem only when
n_samples=2048 matches; otherwise None to fall back to math-
generated twiddles for legacy callers.
- Module docstring updated to reflect post-cleanup history.
test_v7.py — modernise three tests to current production dimensions:
- test_process_chirps_returns_radar_frame: pad input to 2048 samples;
assertions reference NUM_RANGE_BINS / NUM_DOPPLER_BINS from
radar_protocol; n_dop derived from input chirp count.
- test_cfar_enable_changes_detections: 48 chirps x 2048 samples;
output (NUM_RANGE_BINS, NUM_DOPPLER_BINS). No longer skips on
cosim absence — uses synthetic input.
- test_get_frame_raw_iq_synthetic: (2, 48, 2048) raw IQ;
(NUM_RANGE_BINS, NUM_DOPPLER_BINS) output.
- test_cosim_dir: also skip when doppler_map_*.npy absent (matches
_cosim_available pattern in TestSoftwareFPGASignalChain).
Local: test_v7 100/0/0 (9 graceful skips: optional deps + missing
cosim .npy data), test_GUI_V65_Tk 117/0/2. Down from 21 ERRORs.
Mirror the PR-Q.1 PRI stagger (MEDIUM 175 us -> 161 us) into the cosim
scenario generator and regenerate all 12 affected golden hex/csv files.
Without this, the Doppler co-sim TBs would diverge from the RTL on every
MEDIUM sub-frame bin.
- tb/cosim/radar_scene.py: T_PRI_MEDIUM = 161e-6
- tb/cosim/gen_doppler_golden.py: comment update for MEDIUM bin map
- 12 regenerated hex/csv files (doppler + real_data + fullchain_realdata)
Regression: 42/0/1 (PR-Q.1 baseline preserved; T-6 SKIP is scipy-missing).
Resolves AUDIT-C10 (xFFT scaling sim/silicon mismatch) by replacing the
LogiCORE FFT v9.1 BFP setting with deterministic Scaled mode. Schedule
[1,1,…,1] (= /N total) is encoded in radar_params.vh and applied in
both the Xilinx IP via cfg_tdata SCALE_SCH bits and the iverilog
fft_engine fallback via per-stage convergent-rounding >>>1 at every
butterfly write. Output magnitudes now match between sim and silicon —
CFAR alpha calibration is portable.
The /N switch exposed a pre-existing dynamic-range hole in the matched-
filter chain (project_mf_chain_dynrange_defect_2026-05-02): the
frequency_matched_filter.v Q30→Q15 truncation was calibrated for the
BFP-normalized FFT outputs of the BFP era. Under deterministic /N,
chirp energy spreads across bins so each FFT bin is well below Q15
full-scale, and the >>15+saturate crushed chirp / DC / impulse
autocorrelations to zero.
Fix: widen the path between conjugate-multiply and IFFT to 32-bit Q30.
One 32-bit FFT engine instance, AXIS data 64-bit packed
{Q[31:0], I[31:0]}. FWD passes sign-extend their 16-bit ADC/ref
samples; FWD outputs sat-truncate back to 16-bit into sig_buf/ref_buf;
conj-mult emits raw Q30 into a 32-bit prod_buf; IFFT consumes Q30; the
chain saturates 32→16 onto range_profile_*.
bb_mf_test_*.hex regenerated with realistic AGC scaling (peak filled to
~½ ADC range = 16384 LSB) so the cosim chirp scenario exercises the
chain at production-equivalent levels — the bare radar-physics output
sat ~5 LSB below the FFT's per-bin LSB floor.
Test 19 (orthogonal cross-correlation) corrected: under deterministic
/N the cross-correlation of two integer-bin tones is mathematically
zero; the previous "non-zero output" assertion only passed under BFP
because BFP renormalized the noise floor. tb_rxb_fullchain_latency.v
peak-bin gating relaxed to recognize the iverilog fft_engine RX-NEW-1
mirror (peak at bin 2047 instead of 0) as PASS when peak/mean is
healthy.
compare_mf.py "both produce output" gate dropped: zero-but-matching is
valid sim/silicon parity, and the remaining metrics (energy ratio,
magnitude correlation, peak overlap, I/Q correlation) already handle
the zero case via the py_energy == 0 and rtl_energy == 0 → 1.0 clause.
Regression: 42 PASS / 0 FAIL / 1 skip (was 37 PASS / 5 FAIL):
- MF Co-Sim chirp/dc/impulse: PASS (was FAIL on dynamic-range floor)
- MF Co-Sim chirp peak: 4917 at bin 271, peak/mean ~3.4x
- Matched Filter Chain unit: 40/40 PASS (was 34/40)
- RX-B Full-Chain Autocorrelation: PASS, peak/mean ~166x (was 0)
- tb_fft_engine: 12/12 PASS (Parseval, scaling, roundtrip)
The Xilinx IP DCP must be regenerated on the remote Vivado box for
synth and XSim — gen_xfft_2048_ip.tcl + xfft_2048_ip.xci are updated
for input_width=32 / 64-bit AXIS but the .dcp is still pre-PR-O.
Adds the T-6 independent reference drift cosim (PR-M.1, c30be89) as a
gated regression check so any future hand-edit drift in NCO_SINE_LUT,
fft_twiddle_*.mem, or DOPPLER_WINDOW_COEFF surfaces on every run.
run_regression.sh: new "Independent Reference Drift (T-6)" check after
the RX-B autocorrelation block in Phase 3. Plain `python3` (no path
sniffing). Distinguishes three states from the script's exit code +
markers:
rc=0, PASS markers -> PASS (counts toward `passed`)
rc=2, no markers -> SKIP (counts toward `skipped`)
rc!=0, FAIL markers -> FAIL (gates the regression)
compare_independent.py: detects missing numpy/scipy at startup and exits
with code 2 plus a [SKIP] marker pointing at `uv sync --group dev`.
Without that, an environment without scipy crashed mid-script and the
regression captured a partial 3-of-13 PASS count.
pyproject.toml: scipy>=1.13 added to the dev dependency group (used by
fpga_reference.doppler_window_ideal() for analytical Cheby ground truth).
.github/workflows/ci-tests.yml: fpga-regression now installs Python
3.12, sets up uv, runs `uv sync --group dev`, and activates the
resulting .venv before bash run_regression.sh. Without the activate
line the runner's system python3 (no scipy) would resolve first and
the drift check would [SKIP] in CI.
Verified locally:
with venv: Drift PASS (13 checks), Tests: 43 passed / 0 / 0
no scipy: Drift SKIP (msg points at install cmd), 42p / 0f / 1s
T-6 drift cosim (PR-M.1, c30be89) surfaced a 740-LSB / 2.3 % spec-vs-
implementation gap in the Doppler window: doppler_processor.v lines
99..114 and fpga_model.HAMMING_WINDOW were documented as sym Hamming
N=16 (0.54 - 0.46*cos(2*pi*n/15)) but contained values that didn't
match any standard window family. Existing Doppler cosim passed bit-
exactly because both the RTL and the Python twin shared the identical
non-canonical values.
Quantifying the trade with scipy.signal across 11 candidates, the
production LUT actually had peak sidelobes of -33 dB (vs canonical
sym Hamming -40 dB) — the hand-tweaks made it 6.6 dB worse than the
formula it claimed to be. Rather than just fix the LUT to canonical
Hamming, picked Dolph-Chebyshev 60 dB equiripple as a deliberate
upgrade for counter-UAS Doppler where MTI-residual clutter leakage
into adjacent Doppler bins is the dominant false-alarm source.
Window comparison (N=16, Q15):
Window PSL(dB) MLW(bins) ENBW CG(dB) In-bin SNR loss
Old "Hamming" -33.2 1.38 1.45 -5.84 1.61 dB
Canonical Hamm -39.8 1.35 1.43 -5.83 1.54 dB
Dolph-Cheby 60 -60.0 1.48 1.55 -6.48 1.91 dB <-
Kaiser β=8 -57.9 1.69 1.78 -7.77 2.50 dB
Blackman -93.7 1.75 1.84 -8.10 2.66 dB
Cheby-60 buys 27 dB of sidelobe rejection over the old LUT for 0.30 dB
worse in-bin SNR and 7 % wider main lobe — a strict win for cluttered
counter-UAS environments. Hardware impact: zero. The window is a
16-entry Q15 ROM; same reg width, same DSP multiply, same FFT pipeline,
same timing, same area. Only the initial-block hex literals change.
Changes:
* doppler_processor.v lines 114..129: 14 of 16 hex literals replaced
with chebwin(16, at=60) Q15 values; comment block updated
* tb/cosim/fpga_model.py: HAMMING_WINDOW renamed to DOPPLER_WINDOW_COEFF,
values replaced; class comments updated
* tb/cosim/fpga_reference.py: hamming_16_ideal() renamed to
doppler_window_ideal(), uses scipy.signal.windows.chebwin
* tb/cosim/compare_independent.py: import + label updates
* tb/cosim/gen_doppler_golden.py: docstring header
* tb/cosim/doppler_golden_py_*.{csv,hex} (3 scenarios): regenerated
* tb/cosim/real_data/hex/{doppler,fullchain}_doppler_ref_{i,q}.hex:
regenerated via gen_realdata_hex.py
Drift cosim now 13/13 PASS — DOPPLER_WINDOW_COEFF matches its
analytical Cheby-60 ideal bytewise (0 LSB drift). Full regression
42 passed / 0 failed of 42 — bit-exact cosim still passes (RTL ≡
Python twin since both got the new LUT).
Adds tb/cosim/fpga_reference.py: numpy/scipy implementation of NCO,
FFT, matched filter, and Doppler. Unlike fpga_model.py — which is a
bit-exact PORT of the RTL (same NCO_SINE_LUT, same twiddle .mem files,
same Q15 quantization) — this reference computes the algorithm from
analytical formulas with no LUT or quantization. It is the third leg
of the cosim triangle so transcription bugs that exist identically in
both the Python twin AND the RTL no longer hide.
Adds tb/cosim/compare_independent.py: runs canonical stimulus through
both twin and reference and reports drift. Bytewise LUT spot-checks
(NCO_SINE_LUT, fft_twiddle_16.mem, fft_twiddle_2048.mem,
HAMMING_WINDOW) plus end-to-end peak/roundtrip invariants for NCO,
FFT-2048, MF, Doppler.
Findings (12/13 drift checks pass):
* NCO_SINE_LUT, fft_twiddle_16.mem, fft_twiddle_2048.mem all match
their analytical Q15 values bytewise (max dev = 0 LSB) — the two
biggest hand-transcribed LUTs are clean.
* HAMMING_WINDOW [FAIL] — max 740 LSB drift from documented formula
0.54-0.46*cos(2*pi*n/15) at n=5 (LUT=25971, ideal=25231). The
same wrong values appear in fpga_model.HAMMING_WINDOW and
doppler_processor.v lines 99-114; both share the drift, which is
why every existing Doppler cosim has been passing bit-exactly. To
resolve: either regen the LUTs to match the documented formula
and re-bless Doppler goldens, or update the comments to describe
the actual values (no clean closed-form match yet identified).
Not wired into run_regression.sh in this commit so the drift gating
decision (fix vs document) can be made deliberately.
Replaces the legacy ADI CN0566 .npy capture flow with a synthetic radar
scene generated by tb/cosim/real_data/gen_realdata_hex.py via the
existing radar_scene + fpga_model bit-accurate Python models.
Dimensions now match production radar_params.vh:
RP_FFT_SIZE=2048, RP_DECIMATION_FACTOR=4, RP_NUM_RANGE_BINS=512,
CHIRPS_PER_FRAME=48, NUM_DOPPLER_BINS=48 (3 sub-frames x 16-pt FFT).
Previously both TBs were pinned to legacy 32-chirp / 2-subframe / 1024->64
DECIM=16 dimensions. range_bin_decimator.v's 2-bit comparisons against
DECIMATION_FACTOR/2 only behave correctly for small DECIM, so the old
DECIM=16 path no longer worked even though the TBs compiled — that is
why Full-Chain Real-Data was reporting pass=0/fail=3.
Changes:
tb/cosim/real_data/gen_realdata_hex.py (new) - synthesises 6 fixture
files from a 2-target scene via DopplerProcessor (3-subframe) and
RangeBinDecimator (peak, 2048->512). Reproducible (fixed seed 42).
tb/cosim/real_data/golden_reference.py (deleted, 1436 lines) - the
legacy generator depended on out-of-tree ADI .npy captures and
modelled only the 2-subframe / 32-chirp path.
tb/cosim/real_data/hex/ - 43 orphan artifacts deleted (CFAR / MTI /
notched / detection / range-FFT debug dumps that nothing in the
active TB or regression was loading); 6 fixtures regenerated at
production dimensions:
doppler_input_realdata.hex 24576 packed lines (was 2048)
doppler_ref_{i,q}.hex 24576 lines each (was 2048)
fullchain_range_input.hex 98304 packed lines (was 32768)
fullchain_doppler_ref_{i,q}.hex 24576 lines each (was 2048)
tb/tb_doppler_realdata.v - CHIRPS 32->48, RANGE_BINS 64->512,
DOPPLER_FFT 32->48, MAX_CYCLES bumped.
tb/tb_fullchain_realdata.v - same + INPUT_BINS 1024->2048,
DECIM_FACTOR 16->4, fixed
decim_bin_index width to
RP_RANGE_BIN_WIDTH_MAX, fixed
start_bin width 10->11.
run_regression.sh - "Doppler Real-Data" label updated
(no longer "ADI CN0566"); both
realdata tests get explicit
--timeout values (300 / 600 s).
Standalone results:
tb_doppler_realdata - 24584/24584 PASS (3.36 s sim, ~50 s wall)
tb_fullchain_realdata - 24585/24585 PASS (4.10 s sim, ~5 min wall)
Full regression now: 41 passed / 1 failed (only remaining FAIL is
FFT Engine, pre-existing pre-PR-K regex-reveal — unrelated).
T-7 (compare_mf.py): replace "energy ratio 0.001-1000" cargo-cult bounds
with strict Parseval/correlation gates — energy 0.95-1.05, mag_corr >=
0.95, peak_overlap_10 >= 0.90, corr_i/corr_q >= 0.90. All four MF cosim
scenarios still pass (energy=1.000 mag_corr=1.000 peak=1.000) but the
script now bites on any drift instead of rubber-stamping.
T-8 (doppler cosim 32->48): bump cosim/TBs/Python model to production
3-subframe / 48-bin config (PR-F). DopplerProcessor parameterised over
NUM_SUBFRAMES (default 3, legacy 2 still callable). radar_scene now uses
SHORT/MEDIUM/LONG slow-time matching chirp_scheduler.v. Goldens
regenerated; tb_doppler_cosim drops the legacy CHIRPS_PER_FRAME=32
override; all 3 doppler scenarios pass bit-exact (energy=1.0000
peak_agree=1.000 mag_corr=1.000) at production config.
tb_doppler_realdata kept on the legacy override — its goldens are
bit-exact ADI CN0566 captures (32 chirps x 64 range bins) and the
3-subframe regen needs new hardware captures + golden_reference.py
rewrite, deferred to PR-I.
Full regression: 37/41 (same 4 pre-existing T-2..T-5 failures, no new
regressions).
Drop the chirp-v1 1-bit use_long_chirp memory loader and its 6 .mem files;
introduce chirp_reference_rom — wave_sel-native, single 8192x16 BRAM array
per Q15 lane, 4-region init (SHORT, MEDIUM, LONG seg0/seg1) loaded from the
PR-B mem files. Same 1-clk read latency as the legacy module so the RX-B
autocorrelation alignment fix carries through unchanged.
Receiver-side wave_sel shim added in radar_receiver_final.v:
wire [1:0] wave_sel = use_long_chirp ? RP_WAVE_LONG : RP_WAVE_SHORT;
This is a 1-line transitional bridge while radar_mode_controller still
emits 1-bit use_long_chirp; PR-D deletes the shim and wires chirp_scheduler
straight through. MEDIUM is loaded into the ROM but unreachable through
the production path until PR-D.
BRAM cost: 8 RAMB18 (was 6 in chirp-v1). +2 BRAM is the cost of adding
MEDIUM to the waveform set; not avoidable.
Files added:
- chirp_reference_rom.v
Files removed:
- chirp_memory_loader_param.v
- long_chirp_seg{0,1}_{i,q}.mem (4 files)
- short_chirp_{i,q}.mem (2 files)
- tb/cosim/validate_mem_files.py (legacy file-set validator; replaced by
gen_chirp_mem.py's internal verify_phase_match)
- tb/cosim/analyze_short_chirp_mismatch.py (one-shot tool from the
chirp-v1 TX-I investigation; finding incorporated, references the
deleted short_chirp_*.mem files)
Files updated for module rename:
- radar_receiver_final.v — instance, comments, wave_sel shim
- radar_mode_controller.v — header comment
- matched_filter_processing_chain.v — header comment
- scripts/200t/build_200t.tcl — explicit RTL list
- run_regression.sh — 5 spots
- tb/tb_rxb_fullchain_latency.v — instance, wave_sel shim, mem filenames,
SHORT_LEN 50 → 100 (1 µs at 100 MHz)
- tb/tb_system_e2e.v — header comment
Verification:
- chirp_reference_rom standalone iverilog compile: clean
- Full receiver chain compile (21 RTL files): clean
- tb_rxb_fullchain_latency runs end-to-end with new ROM + new mem files
+ 100-sample SHORT chirp; autocorrelation peak at bin 0, peak |I|+|Q|
= 15115. Confirms 1-clk ROM read latency is preserved and the RX-B
direct-wire-with-1-FF alignment still holds.
- 50T build script (scripts/50t/build_50t.tcl) uses glob *.v — no edit
needed; it picks up the new file automatically.
Rewrite gen_chirp_mem.py to emit the SHORT (1 µs), MEDIUM (5 µs), and LONG
(30 µs) waveform set on both TX and RX paths. The script is now the single
source for every chirp .mem file; the legacy 6-file set on disk
(long_chirp_lut.mem, long_chirp_seg{0,1}_{i,q}.mem, short_chirp_{i,q}.mem)
is no longer regenerated and gets deleted in PR-C/PR-E when its consumer
modules are removed.
Generated artifacts (committed):
TX (8-bit unsigned offset-binary, fs_dac = 120 MHz):
tx_short_lut.mem 120 lines
tx_medium_lut.mem 600 lines
tx_long_lut.mem 3600 lines
RX (Q15 I/Q hex, fs_sys = 100 MHz, all 2048 lines for uniform BRAM sizing):
rx_short_i.mem / rx_short_q.mem 100 active + 1948 zero-pad
rx_medium_i.mem / rx_medium_q.mem 500 active + 1548 zero-pad
rx_long_seg0_i.mem / rx_long_seg0_q.mem 2048 (samples [0..2047])
rx_long_seg1_i.mem / rx_long_seg1_q.mem 952 active + 1096 zero-pad
Phase model unchanged from chirp-v1: phi(n) = 2π·F_BASEBAND_LOW·t +
π·(BW/T)·t² with F_BASEBAND_LOW=10 MHz and BW=20 MHz. The same formula now
runs three durations and two sample rates from one helper.
rx_long_seg0_i.mem is bit-exact to the legacy long_chirp_seg0_i.mem on disk
(diff -q reports identical) — proves the SHORT/MEDIUM additions did not
perturb the LONG path.
Verification:
- all 11 files have correct line counts (above)
- script is idempotent (re-run produces byte-identical output)
- ruff clean (one E501 line-length + two RUF046 redundant-int casts fixed)
- phase regression at long-seg0 against pre-chirp-v2 reference: bit-exact
No RTL or testbench changes. The legacy .mem files remain on disk for the
existing chirp_memory_loader_param.v / plfm_chirp_controller.v consumers
until PR-C and PR-E delete those modules. No module references the new
files yet.
Two stale-baseline events were never captured in earlier commits:
1. The FFT-1024 -> FFT-2048 merge (c668652) updated the testbench and
gen_mf_cosim_golden.py but left radar_scene.py FFT_SIZE=1024. When
FFT_SIZE was later bumped to 2048, the input vectors written by
generate_baseband_samples (bb_mf_test_*.hex, ref_chirp_*.hex) grew
from 1024 to 2048 samples but were never re-exported.
2. The TX-I matched-filter realignment (5ff5671) changed the ADC chirp
phase from 2*pi*F_IF*t to 2*pi*(F_IF+F_BASEBAND_LOW)*t. ADC sample
values shifted from sample ~1336 onward but adc_*.hex was never
re-exported.
Result: every regression run produced a "dirty" working tree as the
regen reproduced post-merge values that disagreed with the committed
baselines. Two consecutive regen runs are bit-exact identical
(LCG seed=42 + deterministic chirp math) — verified via diff -q on
two output dirs. There is no actual non-determinism; only stale
artifacts.
This commit refreshes all 15 affected files in one shot:
- 6 input hex (adc_*_target.hex, bb_mf_test_*.hex, ref_chirp_*.hex)
- 5 RTL output csv (rtl_*.csv from current RTL)
- 4 compare csv (compare_mf_*.csv = py vs rtl side-by-side)
Verification: full regression 39/39 PASS on the refreshed inputs.
After this commit, regression runs should leave the working tree clean.
The DAC short/long chirp LUTs are 10..30 MHz upchirps (Hilbert-confirmed).
With TX_LO=10.500 GHz, RX_LO=10.380 GHz (adf4382a_manager.h) and the
120 MHz DDC NCO (ddc_400m.v), high-side mixing places the post-DDC echo
at 10..30 MHz baseband. The matched-filter reference (gen_chirp_mem.py)
was generating 0..20 MHz, implicitly assuming the chirp's low edge mixed
to DC. This caused a 10 MHz spectral offset and ~5 dB matched-filter loss.
Adds F_BASEBAND_LOW=10e6 in both gen_chirp_mem.py and radar_scene.py,
with phase formula 2*pi*F_BASEBAND_LOW*t + pi*rate*t^2 in all chirp
generators. Regenerates the 6 .mem files. Adds analyze_short_chirp_mismatch.py
for the Hilbert-based diagnosis. Fixes the misleading "30MHz to 10MHz"
comment in plfm_chirp_controller.v and adds an end-to-end frequency plan
in the LUT header.
Sideband orientation (high-side at both mixers) is the conventional choice
and consistent with antenna match (10.25..10.75 GHz, 8x16 patch designed
at 10.5 GHz). Loopback capture would settle definitively; if either mixer
is low-side the F_BASEBAND_LOW sign flips and/or chirp direction reverses.
latency_buffer.v has had zero non-tb instantiations since RX-B (2026-04-23)
replaced its hookup in radar_receiver_final with a 1-FF alignment register.
The module was being kept "for potential future use" — exactly the kind of
dead weight the codebase does not need. Deleted, along with all build /
test infrastructure that dragged it along:
- 9_Firmware/9_2_FPGA/latency_buffer.v
- 9_Firmware/9_2_FPGA/tb/tb_latency_buffer.v
- run_regression.sh: removed from RTL_FILES and RECEIVER_RTL
- scripts/200t/build_200t.tcl: removed from synthesis source list
- tb/tb_system_e2e.v: removed from header compile-string example
- tb/cosim/validate_mem_files.py: deleted test_latency_buffer() (~75 lines),
its call site, and the corresponding entry in the module docstring
Historical RX-B comments referencing latency_buffer in radar_receiver_final.v,
tb_rxb_fullchain_latency.v, and tb_rxb_latency_measure.v are kept — they
explain WHY the module was removed, which is still useful design archaeology.
Two doc-only housekeeping touches bundled in:
- plfm_chirp_controller.v: replaced two empty "CRITICAL FIX: Generate
valid signal" labels at LONG_CHIRP and SHORT_CHIRP with one shared
chirp_valid policy comment block above LONG_CHIRP that explains the
actual rationale (downstream FIFO underrun on trailing samples).
- v7/models.py: replaced the "range_resolution and velocity_resolution
should be calibrated" docstring (sounded like an open TODO but was a
documented placeholder) with a clear pointer to the GUI-C3 fix in
workers.py:RadarDataWorker so future readers know the live path
derives correct values from WaveformConfig.
FPGA quick regression unchanged: 28/29 (1 fail is the unrelated iverilog/
Xilinx-IP RX-NEW-3 gap). GUI suite 180/180. Ruff clean.
rx_final_doppler_out.csv is written by tb_radar_receiver_final.v on
every run via $fopen — it is a test-run artifact, not an oracle. It
was mistakenly tracked in an earlier commit, causing unnecessary
churn on every sim. Remove from the index and ignore going forward.
Also ignore stray a.out from iverilog one-shot compiles.
Golden references (.hex, .mem, doppler_golden_py_*.csv) remain
tracked — they are load-bearing oracles used by MF / Doppler /
receiver cosim testbenches.
RTL (P0 pre-bringup findings R-1/R-2/R-3/R-5/R-6):
- mti_canceller: add use_long_chirp input and waveform-boundary mute
so the long->short transition in mode 01 no longer subtracts across
heterogeneous waveforms (R-1). Prev buffer is overwritten in-flight
at the boundary so the next same-waveform chirp subtracts cleanly.
- ad9484_interface_400m: 2FF sync of mmcm_locked into the 400 MHz
domain before gating reset_n_gated (R-6).
- cic_decimator_4x_enhanced: correct max_fanout narrative (R-3).
- ad9484_interface_400m: strip stale pblock comment, note 3.0 ns
max_delay instead (R-2).
- mti_canceller / doppler_processor: 200T-20km WARNING banners
flagging the broken 4096-bin path (R-5). 9-bit BRAM address aliases
silently until rewritten.
- adc_clk_mmcm.xdc: relax set_max_delay from 2.700 -> 3.000 ns,
closes WNS with headroom on 50T build.
- radar_receiver_final: wire use_long_chirp into mti_inst.
Architecture-bump finalization (2048-pt range FFT, 512 range bins,
32 Doppler bins -> 16384 output cells per frame):
- tb/cosim/radar_scene.py: FFT_SIZE 1024 -> 2048, RANGE_BINS 64 -> 512.
- tb/gen_mf_golden_ref.py: N 1024 -> 2048.
- Regenerate all affected hex goldens (MF cases 1-4, Doppler inputs
+ py goldens, receiver integration golden_doppler.mem 2048 -> 16384).
- tb_radar_receiver_final: widen range_bin_out 6 -> 9 bits, bump
GOLDEN_ENTRIES 2048 -> 16384, expand bitmaps/arrays to 512 bins,
update all check messages and thresholds.
- tb_mti_canceller, tb_fullchain_mti_cfar_realdata: tie/pass
use_long_chirp so compile still works after RTL port add.
Test-suite hardening (coverage audit findings):
- tb_mti_canceller T12: 10 new assertions exercising R-1 waveform-
boundary mute across a long/long/short/short/long sequence. Catches
a regression that re-enables subtraction across the boundary.
- tb_fir_lowpass: replace tautological check(1'b1, ...) on coefficient
symmetry with a real hierarchical check coeff[k]===coeff[31-k];
replace always-pass overflow check with a well-driven (not X/Z)
assertion on filter_overflow.
- tb_matched_filter_processing_chain: replace three always-pass peak-
bin placeholders with peak-to-mean-|out| > 2x ratio checks (catches
flat/zero output that the old tautologies silently accepted).
- tb_cdc_modules M2: replace always-pass narrow-pulse check with a
well-defined-output assertion on the synchronizer.
- tb_nco_400m: replace always-pass freq-switch check with a swing +
no-X assertion across 200 post-switch samples.
- tb_system_e2e G12.1: replace check(1, ...) with test_num > 20 so
it catches a stalled TB that skipped prior groups.
- tb_multiseg_cosim TEST 4: replace always-pass placeholder with a
bitmap that asserts segment_request visited all 4 values.
- tb_mf_chain_synth and tb_fullchain_mti_cfar_realdata: add DEPRECATED
headers plus \$fatal guards (ifndef ALLOW_STALE_*) so they cannot
be silently re-enabled in CI with stale 1024-bin goldens against
current 2048-pt RTL.
Regression: 32 passed, 0 failed. MTI TB grew 30 -> 39 checks;
receiver integration grew 17 -> 18 checks with 16384/16384 golden
match at tolerance +/- 2 LSB.
Replace direct !reset_n async sense with a registered active-high reset_h
(max_fanout=50) in nco_400m_enhanced, cic_decimator_4x_enhanced, and
ddc_400m. The prior single-LUT1 / 700+ load net was the root cause of
WNS=-0.626 ns in the 400 MHz clock domain on the xc7a50t build. Vivado
replicates the constrained register into ≈14 regional copies, each driving
≤50 loads, closing timing at 2.5 ns.
Change radar_system_top default USB_MODE from 0 (FT601) to 1 (FT2232H).
FT601 remains available for the 200T premium board via explicit parameter
override; the 50T production wrapper already hard-codes USB_MODE=1.
Regression: add usb_data_interface_ft2232h.v to PROD_RTL lint list and
both system-top TB compile commands; fix legacy radar_system_tb hierarchical
probe from gen_ft601.usb_inst to gen_ft2232h.usb_inst.
Golden reference files (rtl_bb_dc.csv, rx_final_doppler_out.csv,
golden_doppler.mem) regenerated to reflect the +1-cycle registered-reset
boundary behaviour; Receiver golden-compare passes 18/18 checks.
All 25 regression tests pass (0 failures, 0 skipped).
Co-Authored-By: Claude Sonnet 4.6 <noreply@anthropic.com>
golden_reference.py: update comment from 'Simplified' to 'Exact' to
match shaun0927's corrected formula.
fpga_model.py: fix adc_to_signed docstring that incorrectly derived
0x7F80 instead of 0xFF00. Verilog '/' binds tighter than '-', so
{1'b0,8'hFF,9'b0}/2 = 0x1FE00/2 = 0xFF00, not 0xFF<<8 = 0x7F80.
The golden reference used (adc_val - 128) << 9 which subtracts 65536,
but the Verilog RTL computes {1'b0,adc,9'b0} - {1'b0,8'hFF,9'b0}/2
which subtracts 0xFF00 = 65280. This creates a constant 256-LSB DC
offset between the golden reference and RTL for all 256 ADC values.
The bit-accurate model in fpga_model.py already uses the correct RTL
formula. This aligns golden_reference.py to match.
Verified: all 256 ADC input values now produce zero offset against
fpga_model.py.
Regenerate all real-data golden reference hex files against the current
dual 16-point FFT Doppler architecture (staggered-PRI sub-frames).
The old hex files were generated against the previous 32-point single-FFT
architecture and caused 2048/2048 mismatches in both strict real-data TBs.
Changes:
- Regenerate doppler_ref_i/q.hex, fullchain_doppler_ref_i/q.hex, and all
downstream golden files (MTI, DC notch, CFAR) via golden_reference.py
- Add tb_doppler_realdata (exact-match, ADI CN0566 data) to regression
- Add tb_fullchain_realdata (exact-match, decim->Doppler chain) to regression
- Both TBs now pass: 2048/2048 bins exact match, MAX_ERROR=0
- Update CI comment: 23 -> 25 testbenches
- Fill in STALE_NOTICE.md with regeneration instructions
Regression: 25/25 pass, 0 fail, 0 skip. ruff check: 0 errors.
Resolve all 374 ruff errors across 36 Python files (E501, E702, E722,
E741, F821, F841, invalid-syntax) bringing `ruff check .` to zero
errors repo-wide with line-length=100.
Rewrite CI workflow to use uv for dependency management, whole-repo
`ruff check .`, py_compile syntax gate, and merged python-tests job.
Add pyproject.toml with ruff config and uv dependency groups.
CI structure proposed by hcm444.
- Remove xfft_32.v, tb_xfft_32.v, and fft_twiddle_32.mem (dead code
since PR #33 moved Doppler to dual 16-pt FFT architecture)
- Update run_regression.sh: xfft_16 in PROD_RTL, remove xfft_32 from
EXTRA_RTL and all compile commands
- Update tb_fft_engine.v to test with N=16 / fft_twiddle_16.mem
- Update validate_mem_files.py: validate fft_twiddle_16.mem instead of 32
- Update testbenches and golden data from main_cleanup branch to match
dual-16 architecture (tb_doppler_cosim, tb_doppler_realdata,
tb_fullchain_realdata, tb_fullchain_mti_cfar_realdata, tb_system_e2e,
radar_receiver_final, golden_doppler.mem)
- Update CONTRIBUTING.md with full regression test instructions covering
FPGA, MCU, GUI, co-simulation, and formal verification
Regression: 23/23 FPGA, 20/20 MCU, 57/58 GUI, 56/56 mem validation,
all co-sim scenarios PASS.
- radar_system_top.v: DC notch now masks to dop_bin[3:0] per sub-frame so both sub-frames get their DC zeroed correctly; rename DOPPLER_FFT_SIZE → DOPPLER_FRAME_CHIRPS to avoid confusion with the per-FFT size (now 16)
- radar_dashboard.py: remove fftshift (crosses sub-frame boundary), display raw Doppler bins, remove dead velocity constants
- golden_reference.py: model dual 16-pt FFT with per-sub-frame Hamming window, update DC notch and CFAR to match RTL
- fv_doppler_processor.sby: reference xfft_16.v / fft_twiddle_16.mem, raise BMC depth to 512 and cover to 1024
- fv_radar_mode_controller.sby: raise cover depth to 600
- fv_radar_mode_controller.v: pin cfg_* to reduced constants (documented as single-config proof), fix Property 5 mode guard, strengthen Cover 1
- STALE_NOTICE.md: document that real-data hex files are stale and need regeneration with external dataset
Closes#39
- usb_data_interface.v: Add 3 self-test status inputs, expand status packet
from 7 words (header + 5 data + footer) to 8 words (header + 6 data + footer).
New status_words[5] carries {busy, detail[7:0], flags[4:0]}.
- radar_system_top.v: Wire self_test_flags_latched, self_test_detail_latched,
self_test_busy to usb_data_interface ports. Add opcode 0x31 as status
readback alias so host can read self-test results.
- tb_usb_data_interface.v: Add self-test port connections, verify word 5 in
Group 16, add Group 18 (busy flag + partial failure variant). 81 checks pass.
- run_regression.sh: Add fpga_self_test.v to PROD_RTL lint list and system-
level compile lists. Add tb_fpga_self_test as Phase 1 unit test.
- 24/24 regression tests pass, lint clean (0 errors, 4 advisory warnings).
RTL fixes discovered via new end-to-end testbench:
- plfm_chirp_controller: TX/RX mixer enables now mutually exclusive
by FSM state (Fix#4), preventing simultaneous TX+RX activation
- usb_data_interface: stream control reset default 3'b001 (range-only),
added doppler/cfar data_pending sticky flags, write FSM triggers on
range_valid only — eliminates startup deadlock (Fix#5)
- radar_receiver_final: STM32 toggle signals wired through for mode-00
pass-through, dynamic frame detection via host_chirps_per_elev
- radar_system_top: STM32 toggle signal wiring to receiver instance
- chirp_memory_loader_param: explicit readmemh range for short chirp
Test infrastructure:
- New tb_system_e2e.v: 46 checks across 12 groups (reset, TX, safety,
RX, USB R/W, CDC, beam scanning, reset recovery, stream control,
latency budgets, watchdog)
- tb_usb_data_interface: Tests 21/22/56 updated for data_pending
architecture (preload flags, verify consumption instead of state)
- tb_chirp_controller: mixer tests T7.1/T7.2 updated for Fix#4
- run_regression.sh: PASS/FAIL regex fixed to match only [PASS]/[FAIL]
markers, added E2E test entry
- Updated rx_final_doppler_out.csv golden data
Adds two-layer lint pass (iverilog -Wall + custom static checks) that
catches part-select OOB errors and case-without-default warnings before
pushing to remote Vivado. Catches the exact Synth 8-524 class error that
broke Build 18 initial attempt. Lint errors abort regression; warnings
are advisory. Regenerated golden data for BRAM-migrated matched filter.
CDC fixes across 6 RTL files based on post-implementation report_cdc analysis:
- P0: sync stm32_mixers_enable and new_chirp_pulse to clk_120m via toggle CDC
in radar_transmitter, add ft601 reset synchronizer and USB holding
registers with proper edge detection in usb_data_interface
- P1: add ASYNC_REG to edge_detector, convert new_chirp_frame to toggle CDC,
fix USB valid edge detect to use fully-synced signal
- P2: register Gray encoding in cdc_adc_to_processing source domain, sync
ft601_txe and stm32_mixers_enable for status_reg in radar_system_top
- Safety: add in_bin_count overflow guard in range_bin_decimator to prevent
downstream BRAM corruption
All 13 regression test suites pass (159 individual tests).
New testbenches:
- tb_latency_buffer.v: 13/13 tests for BRAM delay line (P1-3)
- tb_cdc_modules.v: 27/27 tests for all 3 CDC primitives (P1-4)
- tb_ad9484_xsim.v: XSim testbench for AD9484 with Xilinx BUFIO/IDDR
- tb_nco_xsim.v: XSim testbench for NCO DSP48E1 path verification
Fixes:
- tb_usb_data_interface.v: updated test 33 from divide-by-2 check to
ODDR-style clock forwarding verification (39/39 pass)
- rx_final_doppler_out.csv: updated golden reference after bug fixes
RTL fix: matched_filter_multi_segment.v ST_WAIT_FFT now waits for
processing chain to complete ALL 1024 outputs and return to IDLE
before advancing to next segment. Previously, it transitioned on the
first fft_pc_valid edge, causing the chain to still be outputting
while multi-seg started collecting data for the next segment. This
broke the handshake and caused permanent deadlock after segment 0.
Also fixes forward reference of sample_addr_from_chain in
radar_receiver_final.v (declaration moved before first use).
New files:
- tb/tb_radar_receiver_final.v: P0 integration test for full RX
pipeline (ADC->DDC->MF->range_bin_decimator->doppler), 10 checks
- tb/ad9484_interface_400m_stub.v: behavioral ADC stub for iverilog
All existing tests still pass: multi-seg 32/32, MF co-sim 3/3,
Doppler co-sim 14/14.
Jason